M-16 / M16A1 Full Bird Cage Flash Hider. This is the standard "full bird cage" flashhider that came into use in 1967. Will fit all standard threaded 1/2 x 28 AR-15 / M-16 rifles. Learn More
"Hollywood" M-16 Blank Adapter (BFA) for M16 / AR15 Rifles. These are "Hollywood" BFAs and cannot be seen when installed. Simply remove the flash hider and drop in the adapter with the narrow end facing the out towards the end of the flash hider and the broad end against the base of the muzzle. Blank adapters are machined from cold rolled 1018 steel for durability.
Priced per BFA.
We make three different sizes for these blank adapters:
USGI blanks and Euro NATO surplus are the weakest blanks and use the smallest aperture.
LAM blanks are a "mid-grade" blank with a loud retort, but not as loud and not as much flash as the Swanson Hot blanks.
SWANSON HOT blanks are the loudest / strongest blanks on the market.
USGI - for M200/M200A1 blanks (0.080)
LAM - for Atlantic Wall "LAM" mid-power blanks (0.125)
HOT - for Swanson's Motion Picture Blanks (0.175)
CHECK FIRED BRASS FOR DAMAGE. IF THE BRASS IS MANGLED, THE APERTURE IS TOO TIGHT AND NEEDS TO BE OPENED. IF YOU ARE UNSURE, ASK THE MANUFACTURER OF YOUR BLANKS WHAT SIZE HOLE HE RECOMMENDS! FAILURE TO USE THE CORRECT DIAMETER HOLE CAN RESULT IN SERIOUS PERSONAL INJURY AND / OR DAMAGE TO YOUR RIFLE! Learn More
"Hollywood" M-14 Blank Adapter (BFA) for M14 / M1A Rifles. These are "Hollywood" BFAs and cannot be seen when installed. Simply loosen the set screw on the front of the site base, remove the castle nut, remove the flashider, inset the adapter into the flashider (narrow end out) and reassemble. Priced per BFA, flashider not included. Blank adapters are machined from cold rolled 1018 steel for durability.
All of our M14 BFA's come with the "starter" stock aperture size of 0.110 which should work in most rifles with the weaker Austrian L31A1 blanks. It will also work as a pilot hole to drill them out for more powerful blank loads (primarily European military .308 blanks or USGI Blanks). It is important to note that even though they use same nomenclature designation, there can be a difference in power based on country of origin. For example, British Radway Green L31A1 blanks (head stamp RG) are hotter than Austrian L31A1 (head stamp HP). For most blanks, you will need to enlarge the hole. Below are some rough guidelines for sizes that we have found to work. This is very important!
Guidelines for Drilling Out Blank Adapters:
Swanson (.187)
USGI Blanks (.171)
Radway L31A1 Blanks (.136)
Austrian L31A1 Blanks (.110)
*These sizes work in both semi and full auto in a USGI H&R M14. They may take some tweaking for your rifle. Speak with the manufacturer of your blanks to get a ballpark starting range! This information is included as a guide. We are not responsible for damaged weapons or body parts!
CHECK FIRED BRASS FOR DAMAGE. IF THE BRASS IS MANGLED, THE APERTURE IS TOO TIGHT AND NEEDS TO BE OPENED. IF YOU ARE UNSURE, ASK THE MANUFACTURER OF YOUR BLANKS WHAT SIZE HOLE HE RECOMMENDS! FAILURE TO USE THE CORRECT DIAMETER HOLE CAN RESULT IN SERIOUS PERSONAL INJURY AND / OR DAMAGE TO YOUR RIFLE
Learn More
Standard issue "Shoulder Holster" for the M-1911 pistols (will also fit the Beretta M9 series) . Commonly seen in use by aviators, tankers, etc. These holsters are in new condition and made by government contractors. They are not import copies. Holsters are complete with NSN codes, etc. Learn More
Standard issue "Hip Holster" for the M-1911 and M-1911A1 pistols. These holsters are genuine military contract holsters. Holster manufacturer on back may vary depending on availability, but they are all marked and have the government contract number. These are all "real" USGI holsters. Hard to find real holsters and you can't beat the quality! Holsters are in unissued condition.
Because these are New Old Stock, you need to exercise care when first opening the holster. The leather is tight and dry and if you just pull on the flap, you WILL pull out the male press stud and ruin the holster. You need to gently work the flap the first couple of times and it is even better if you condition the leather and then use care opening. Once they have been used, there is no problem. Learn More
Standard issue "Hip Holster" for military / police revolvers .38 revolvers. These holsters are quality, new made reproductions. Holster flap closure has a lift the dot closure and GI contract manufacturer information stamped on back as well as a 1966 DSA. This style of holster has become harder to come by and now there are some quality reproductions for field use. Learn More
M-67 "Tri-Fold" E-Tool & Cover. Vietnam era dated, both shovel and cover are 1975 or earlier. E-tools / shovels are in VG+ to EXC condition. Covers are in unissued condition. You can find 80's and 90's dated shovels easily but the earlier dated shovels are hard to come by. Entrenching / Intrenching Tool Learn More
M-67 Ammunition Pouch, 20rd. We have two conditions available currently:
Fair to Good (F/G) used are in heavy used condition but will still work for magazines. Most of these have good solid nylon canvas bodies, but the the suspender strap is missing and the side grenade straps have been removed. Some have a cracked main buckle closure and others have had the buckle closure replaced with snaps. Despite the flaws and or repairs, all will close and will work to hold magazines.
Very Good + to Excellent - (VG+/EXC-) show some use light some wear, but they have all parts present and functioning to include snaps and suspender strap. These are complete pouches showing minimal wear and are good solid pouches that still look pretty good.
All priced per pouch. Learn More
M-67 Sleeping Roll Carrier. Overall VG+ to EXC- used condition. May show light signs of use. They attach to the snaps on the M-67 Suspenders. Learn More
